mode analysis for hollow core photonic crystal fiber
Hi, Is there anyone has experience doing mode analysis for the hollow core photoni crystal fiber? I tried to build the model but cannot find the confined mode although I am pretty sure the parameters I...
View Articlemaximum (or minimum) value in a time domain
Hi, I have a problem I cannot solve and you might help me. In my time-dependent analysis I would like to know the maximum of value of a variable, which has been reached at previous time steps. But I...
View ArticleHow to loop simulations in Comsol 4.2a with Matlab
Dear comsolers, here is an example on how to loop simulations. I'll let you decode it. 'Preprocessing' that I did before the loop: 1. Build a model in Comsol (attached). 2. Save As Model M-File...
View ArticleJoule Heating with Thermal Expansion Simple Setup
Good Afternoon Everyone, I am new to COMSOL but have used other software for simulations (ANSYS), I am currently trying to model an aluminum wire embedded in a polyethylene substrate, just doing a 2D...
View ArticleMetal film with subwavelength size hole: Transmmittance and reflectance study
Hi I'm novice in comsol RF simulation. I'm trying to simulate transmittace and reflectance throught metal film with subwavelength size hole. My structure will consists of Air/metal/semiconductor...
View Articledoes a periodic boundary condition for u implement inflow u (boundary1) =...
Dear everyone, I have a question about the implementation of periodic boundary conditions for fluxes, so that the inflow through one boundary equals the outflow through the other. In comsol 3.5, this...
View Articleelectromagntic propagation through three layers
hello I am student on electronic and I am trying to simulate with comsol on rf module , in summarize my work is to simulate the sun light propagation through three layers bonded to each other and I had...
View Articlemf and mef huge difference
Hi, I want to compare mf and mef physics in order to know which one I have to use for my study. I work with a coil and a conductive core. I'm interesting in the electromagnetic power dissipated in...
View ArticleWhat is the exact electric field expression when using the PORTs? -...
Dear all, In the attached 2D model, I use 'Electromagnetic Waves frequency domain' and I would like to study the light propagation inside my structure. I would like to have a input power flow at port 1...
View ArticleVariable exchange between Matlab and Comsol
Hello everyone, I am running Comsol using the LiveLink with Matlab and am trying to do the following: I have a value, dt, which is 0 everywhere in the beginning. (I can either use dt=0, make an...
View ArticleError in compile Equation: Frequency Domain
Hello everybody, I am simulating a microwave devise in optical frequencies but I see this error: Feature: Compile Equations: Frequency Domain (sol1/st1) Error: error in multiphysics compilation I would...
View ArticleVariable change with time
I have a question about variable change with time. I try to make a mass transfer model. The inflow concentration change with time. If t <= 1000s then C=1mol/m^3 else C=0 I upload the data and make a...
View ArticleStructural Mechanics Equation System
I am trying to understand how my structural mechanics model is computing its solution. The model solves and gives me a reasonable solution. However, I don't understand how it is arriving at its answer....
View ArticleElectromagnetic Induction Tomography simple model
Hi, I am trying to make a very simple 2D model where I have 2 coils in which in between is a medium (air). One of these coils will be excited and have a magnetic field in the direction of the second...
View Articlefor NdFeB magnet, which constitutive relation is closer to reality
I'm modeling two NdFeB magnets placed very close to each other in a repulsive manner. I need to compute the repelling force between them. There are two options for the constitutive relation. One is B =...
View ArticleConvergence issue with nano pore electrodeposition model
I am trying to model electrodeposition into a nanopores but am having troubles with convergence. My solution only converges to 1e3 fairly consistently even if I refine the mesh and then it starts to...
View ArticleCFD - Surface roughness
Hey guys I really need your help on this one! I was wondering if any of you could tell me about the default settings of surface roughness's in COMSOL? All I've found about it in the documentation is...
View ArticleWhen I have to use 2d or 3d modeling?
Hi Everybody! I´m Wagner, from Brazil and I have a question, a simple question I think! How I decide if my modeling will be in 2d or in 3d? I have Heat Transfer and AC/DC model and I work calculating...
View ArticleHeat Transfer in Fins- Help needed
I am trying to simulate a heat sink, very similar to the one shown in the tutorials... In spite of building a coarse mesh, the solution does'nt converge even after 2 hours of solving. I have an i5...
View Article